Jim Roten 52 Ford

 

JIM ROTEN 52 FORD

 

Jim Roten Acquired his 1952 Ford Convertible in 1954. He started customizing it right away. Over the next few years the car developed in a wonderful styled Mild Custom.



By Jim Roten


Jim Roten from Chico California has been¬†into custom cars since he was a teenager. In 1954 Jim bought an slightly used 1952 Ford Convertible, and of course he could not leave it alone and started to do some mild restyling right away, to improve the looks of his new ride.¬†Jim Roten has a keen eye when it comes to Custom Restyling, he would be come close friends with Chico Customizer Riley Collin’s for which Jim did a lot of design work in the 1950’s. Riley Collins was also responsible for the more serious Custom Restyling on Jim’s 1952 Ford that would be done in the mid 1950’s. Jim took plenty of photos along the way to document the changes made to his Ford from 1954 till around 1956.


CCC-chico-california-map



1952 Ford Version One

CCC-jim-roten-52-ford-conv-01Jim with his near new 1952 Ford in 1954. Mostly stock, but there are some custom hubcaps and accessory bumper guards, and many custom dreams.
[divider]


CCC-jim-roten-52-ford-conv-02All the emblems and handles were still in place.
[divider]


CCC-jim-roten-52-ford-conv-03A little later the hood was nosed,the bumper guards removed and stock grille was replaced with a 1953 unit with custom center piece.
[divider]



CCC-jim-roten-52-ford-conv-grille



1952 Ford Version Two

After driving the car around with just a few small Custom Restyling touches it was time to get a little more serious. Jim had his friend Riley Collins in Chico remove all the emblems, trunk handle and side trim on the rear quarters. As was the norm for most Custom Restyled cars in those days, the fresh body work was covered in primer and the car was ready for more cruising. Jim’s white car had dark gray primer spots for some time, it was cool to drive the car like that, it showed you were working on your car, improving its looks.¬†Back in those days¬†most people¬†proceeded on a custom build only as they¬†could afford it, which was usually a series of small steps at a time. Throughout the process the¬†cars were used as daily transportation.

CCC-jim-roten-52-ford-conv-04The stock taillights lenses had been replaced with 1956 Oldsmobile Starfire units.
[divider]


CCC-jim-roten-52-ford-conv-05Jim replaced the moon hubcaps with¬†1956 Oldsmobile hubcaps. Here Jim’s in progress Ford is parked behind his¬†friend Joe Navarro’s¬†Chevy Hard-Top. Primer spot parade…
[divider]


CCC-jim-roten-52-ford-conv-06Joe Navarro¬†Chevy Hard-Top with primer spots shows it was really common to drive your car around like this for some time. .¬† It too, was in the early stages of customizing by Riley Collins.¬†Notice that Jim’s Ford has a slight tail dragging stance, while his friends Chevy has a slight forward rake (California Rake).
[divider]


CCC-jim-roten-52-ford-conv-07A little more work was done, but it still was not time for a full paint-job yet….
[divider]


CCC-jim-roten-52-ford-conv-08Some more fine tuning on the molded headlights, new 1953 Ford spear on the rear quarter and now it was time to get the interior and new top done Bill Luckenbill did the interior work as well as the really great looking Carson-type folding top in white canvas.
[divider]


CCC-jim-roten-52-ford-conv-24Looking good.. and almost ready for paint. Only the door handles needed to come of and then the car was ready for it first copper paint job.
[divider]


CCC-jim-roten-chico-lancers-plaqueJim Roten was a member of the Chico Lancers Car Club.
[divider]


CCC-jim-roten-52-ford-conv-09By now the door handles were shaved and Riley Collins painted the car in a wonderful copper color.
[divider]


CCC-jim-roten-52-ford-conv-10Jim also added a set of fender skirts at this time, and the taillight rings were molded to the rear fender for an smoother look, similar to that of the front fender / headlight.
[divider]


CCC-jim-roten-52-ford-conv-12Some time later Jim added 1956 Dodge grille bar teeth to the grille, added white pin-striping an replaced the hubcaps with 1954 Mercury units to which he added center bullets. Jim Also added a second spotlight on the passenger side of the car.
[divider]


CCC-jim-roten-52-ford-conv-13A good look at the Bill Luckenbill interior and the Carson-type folding top.
[divider]

CCC-jim-roten-52-ford-conv-14Close up photo shows the 1956 Dodge grille teeth added to the grille bar and the pin-striping on the hood and front fender.
[divider]


CCC-jim-roten-52-ford-conv-15Only one color photo remained of this version of the car.
[divider]


CCC-jim-roten-52-ford-conv-11October 1956 ooops…. time for some more custom restyling.
[divider]




1952 Ford Version Three

Before the accident Jim’s Car had all the emblems and door handles shaved. It had solenoid-operated doors and deck lid. The headlights and taillights were frenched. Taillight lenses were 1956 Oldsmobile Starfire. For the new updated version Jim took his Ford of course to his friend Riley Collins who would round the hood¬†corners and fabricated a new¬†grill surround and molded splash pan. A new¬†floating grill was made up from ’53 Studebaker grill bars with turn signals for the top portions. These two units were neatly freched into round rod shaped openings. An¬†1952 Oldsmobile center bar was used on the bottom of the opening. To the grille bar Jim added¬†1956 Dodge grill teeth. Forward side trim on the doors came from a 1956 Pontiac.

The rear quarter panels were reshaped and teeth from a 1954 Mercury were used.¬†The side trim on the rear quarters comes from a 1953 Ford. The hubcaps for this version are 1956 Oldsmobile again. The smaller spotlights were replaced with real Appletons. The car was lowered all around about four inches. And when it came time for¬†paint, Jim was inspired by Geore Sein’s Barris Kustoms restyled 1932 Ford 5-window coupe. Paint job was done by Riley Collins in nitrocellulose lacquert¬†two-tone copper¬†and¬†lime gold.¬†Customization was completed by July 1957.

CCC-jim-roten-52-ford-conv-16Riley Collins¬†with Jim’s Ford.¬†He was preparing the car at an auto show¬†shortly after he¬†finished it in Copper and lime gold ’53 Ford in the summer of 1957. Jim had already joined the Navy by then.
[divider]


CCC-jim-roten-52-ford-conv-17Wonderful lines on Jim’s Ford created by the custom side trim and body work. It really shows Jim design skills.
[divider]


CCC-jim-roten-52-ford-conv-18Notice how nice the side trim follows the shape of the new top. Jim also added new bumper guards to the bumpers for the final version.
[divider]


CCC-jim-roten-52-ford-conv-19Jim’s Ford was for both shows as well as regular road use.
[divider]


CCC-jim-roten-52-ford-conv-20This final version has the fender skirts removed again, which gives the car a more sporty look.
[divider]


CCC-jim-roten-52-ford-conv-21Good look at the new grille in Jim’s Ford. ’53 Studebaker bars on the top, ’52 Olds bar on the bottom with 56 Dodge teeth. The new rounded hood corners have the same radius as the headlights.¬†
[divider]



CCC-jim-roten-52-ford-conv-22

CCC-jim-roten-52-ford-conv-23Jim Roten with his 1952 Ford final version in April 1957.
[divider]



Not too long after the car was¬†completed in¬†July 1957, Jim enlisted in the US Navy¬†and soon after that he sold the car. Jim¬†was only 17 years old when I¬†acquired the car and 20 when it was sold.¬†He has no idea what happened to it after that, and its¬†present day whereabouts are unknown. Hopefully one of our readers might know more about Jim’s old 1952 Ford and knows what happened to it after 1957.
Click HERE to see more of Jim Roten’s amazing Collection.




[divider]

(this article is sponsored by)

CCC-sponsor-ad-kustoms-illustrated-2016-01


[divider]




.

0

Jim Roten Barris Representative

 

BARRIS REPRESENTATIVE

 

Mike Roten, Jim Roten’s son, send us an interesting photo showing an Barris Kustom Products Business Card with his father Jim Roten listed as the Barris Northern California Representative. Of course we needed to find out more about this.

 
 
We have been sharing some more material from the Jim Roten Collection, and stories here in the Custom Car Chronicle in the past. Jim did some really great Custom design work in the Northern California area, working closely with Riley Collin’s Custom Shop in Chico California. We also knew about the friendship of Jim with Sam Barris, but when Jim’s son Mike Roten send us a photo showing a business card from his fathers collection where Jim Roten was listed as a Barris Kustom Product Northern California Representative, we where a bit surprised, and naturally we wanted to know more about this Business Card, and what was behind it all.
 

CCC-barris-kustom-product-roten-cardThe Barris Kustom Products Business Card that was made for Jim Roten. Northern California Representative for the Barris Kustom Products.
[divider]

 
 
We asked Jim Roten about the Barris Business Card his son has send us. Jim replied that he was really surprised that Mike still had those old Business Cards, he had not thought about those in many decades.

Jim mentioned that a car show was coming up in Woodland, California, in 1961, perhaps 1962. Sam Barris was entering the 1957 Chevy “El Capitola” custom for the owner, the Taggart Brothers from Ohio. Sam thought it would be a good idea to promote¬†some of the car wax/detailing products being marketed by George under the Barris Kustom Products line. Sam suggested that Jim Roten have a Barris Business Cards printed so that he would be an approved vendor at the show. Hundreds of sample jars of Barris Carnauba Wax, other Barris Kustom Products hand outs and Jim’s Business Cards were given away during the event. Jim Roten specifically stated that he¬†was never employed by Sam or the Barris Kustom Shop though.¬†
 

CCC-barris-kustom-glaze-hand-outDie-cut bottle shaped cards were given away at shows to help promote the Barris Kustom Products.
[divider]

 
 
Thinking back about this after all these years, Jim thinks it might have been Sam’s way of getting rid of several cartons of the Barris Kustoms Wax that were taking up valuable space in his shop. Sam had already moved back from Los Angeles to Carmichael, nearby Sacramento a few years ago, and he must have realized that he would soon move on to stop working for the Barris Kustom Shop.
 

CCC-barris-cleaning-product-photo-01Barris Kustom Products created a line of Custom Car Care products in the early to mid 1950’s.
[divider]

 
 

CCC-barris-cleaning-product-waxBarris Kustom Products Kolor Wax, sample bottles of this product were handed out at the Woodland show by Jim Roten.
[divider]

 
 
CCC-barris-kustom-product-ad-01Towards the later part of the 1950’s the Barris Kustoms Care Products developed some more and the Barris shop ran some ads in the popular Hot Rod and Custom Car magazines to promote the products.
[divider]
 

CCC-sam-barris-kustom-auto-cardMike also send a picture of this Sam Barris Business Card I had never seen before. Very interesting the Barris Kustom Auto shop in Carmichael California. Jim had taken Sam’s card at this same Woodland Car Show.
[divider]

 
Jim also remembered that Sam Barris was very happy after the show. The last real Barris Kustoms Custom he had created, the El Capitola, took the top award at Woodland show.¬† Its stiffest competition was Gene Winfield’s Jade Idol. Jim has fond memories about the show and spending the time there with Sam Barris.The El Capitola is an amazing Custom Car, which shows Sam Barris great body working and design skills.
 

CCC-sam-barris-el-capitola-dave-jenkins
Dave Jenkins took this nice color slide of the El Capitola. However this photo was not taken at the Woodland show. Jim did not take any photos at the show
[divider]
 
 

CCC-barris-kustom-glaze-decalTo help promote the Barris Kustom Products even more Barris also had these Barris Kustom Glaze water decals made. These were given away at car shows and when you bought the product.
[divider]

 
 

CCC-barris-cleaning-product-boxA year, perhaps two after the show the Barris Kustom Products were developed some more and a nice packaging box was developed. (Rik Hoving Collection)
[divider]

 
 

CCC-barris-cleaning-product-box-02This is how the box looked with the product inside… although these bottle labels have faded in the last 40 plus years. (Lars Hellgren Collection)
[divider]

 
 
 

 

(this article is made possible by)

ccc-sponsor-ad-customs-by-flash-w
 
[divider]
 

CCC-Sponsor-KingKustomsTShirt-602Contact Rob Radcliffe at King Kustoms for more info on these T-Shirts Email Rob

[divider]

.

 
 
 
.

0

Bertolucci 1948 Mercury

 

BERTOLUCCI 1948 MERCURY

 

Jim Roten’s photos of his friend’s Ron Zimmerman’s 1948 Mercury identified as the Dick Bertolucci built Johnny Lehman 1948 Mercury.



In 2008 I came across the amazing Jim Roten Photo Collection. A collection of mostly mid to late 1950’s custom Car photos. Amongst all these photos there where a couple of photos that looked to be older. Three of them showed¬†an¬†1946-48 Mercury convertible with padded top in a typical late 1940’s or early 1950’s style. At the time I tried to get in touch with Jim, to ask him about his amazing photo collection, but in particular the photos of this 1946 Mercury.¬†Other than Jim giving me permission to ad his collection to the Custom Car Photo Archive Jim did not really mention much about his collection.

It is now 2014, and I have been in conatact with Jim, with the help of his son Mike. And Jim is sharing a lot of information about the photos he took in the 1950’s,¬†as well as other great stories from way back when. So I asked Jim about the story behind the 1946-48 Mercury in his collection. It turned out that the Mercury convertible belonge to a close¬†friend of Jim’s, Ron Zimmerman. Ron¬†bought the car in 1954.¬†And¬†perhaps even more important was the fact that Jim mentioned that Ron had never been able to find out much more on the cars history, other than that it was build by Dick Bertolicci in the late 1940’s.

CCC-johnny-Lehman-48-merc-bertolucci-01A young Dick Bertolucci in 1949 in front of his shop with the in progress 1948 Mercury owned by Johnny Lehman. (Photo courtesy of Garage Magazine)
[divider]




Johnny Lehman

I already had created a list of cars and builders that could help me identify this Mercury several years earlyer, and one of the cars on this list was Johnny Lehman’s 1948 Mercury build by Dick Bertolucci. Not having enough info or photos to make a positive identification back the, the new information provided by Jim, directly from the 1954 owner Ron Zimmerman gave me enough input to be able to finally do a positive ID on the three photos in the Jim Roten Collection.

The Mercury was build in 1949 by Dick Bertolucci for owner Johnny Lehman and was shows in the early 1950’s Sacramento area as well as being used on the roads as Johnny regular ride. This story on the CCC is not complete, since we have been unable to find much info on the car before and after Ron owned it. But we hope this article will help find some more info on this cars early years, as well as what happened to it after Ron Zimmerman sold it. If any of the readers knows anything more about this car,¬†please let us know, we would love to add your story to the article.

CCC-johnny-Lehman-48-merc-bertolucci-03Johnny’s Mercury at an early 1950’s Sacramento Car Dealer show. 1949 Mercury bumpers and taillights were used to update the 1948 Mercury. They work really well on the car.¬†(Photo courtesy of the¬†Don Montgomery books)
[divider]


CCC-johnny-Lehman-48-merc-bertolucci-02The Bertolucci 1948 Mercury¬†the same early 1950’s Sacramento show as above.¬†(Photo courtesy of the¬†Don Montgomery books)
[divider]


CCC-johnny-Lehman-48-merc-bertolucci-04Most likely the padded top was produced by Hall in Oakland. A lot of Nor Cal Custom used Hall for their padded tops. (Photo courtesy of Garage Magazine)
[divider]




The Ron Zimmerman years

Ron¬†Zimmerman now lives in¬†Shingletown, in the northeast of Weed, California. He was 18 years old when he purchased the Bertolucci 1948 Mercury in finished condition in 1954. Ron and Jim Roten were¬†seniors at Chico High School.¬†Ron bought the car for a¬†man by the name of Smiley, from Sacramento, Ca.¬†At this time we are not sure if Smiley and Johnny Lehman are the same person, perhaps they are, perhaps Smiley was already a new owner after Johnny. Smiley did mention when Ron bought the car that the car was originally¬†built by Bertolucci in Sacramento in the late 1940’s.

CCC-ron-zimmerman-bertolucci-roten-01Jim took the three photos of Ron’s Mercury in front of Ron’s¬†house in Chico, California in 1955. Sadly the photos have been faded and cracked badly, but we still can see the super straight body work and perfect reflections.
[divider]


CCC-ron-zimmerman-bertolucci-roten-02The headlights were frenched, the¬†fenders molded to the body and the windshield was chopped mildly. The lowered stance was absolutely perfect and the wide white wall tires, Cadillac Sombrero’s and Appleton Spotlights are all so perfect for the time the car was originally build.¬†
[divider]



According to Jim and Ron, the workmanship on that car was spectacular. Bertolucci had chopped the windshield, molded in the fenders front and rear nosed the hood and decked the trunk, lowered the car all around. The fender trim pieces were removed and all holes filled and at the front the parking lights were removed for a much cleaner look. Dick also molded the headlights rings to the fenders, installed 1949 Mercury taillights and modified a set of 1949 Mercury bumpers to fit the 1948 Mercury. The 1949 Mercury bumpers wrap around the fenders more than the original bumpers giving the cr a much more modern look.

The bodywork was arrow straight.¬†it was¬†finished in flawless black lacquer.¬†The interior was done in red and white naugahyde with dark red carpets. The dash was chromed as were the garnish rails.¬†The car¬†had a perfect stance…. and the just “right look”.¬†It had a 3/4 race Mercury 59AB flat head engine with three carburetors, a hot cam, aluminum heads, and headers.¬†According to Jim Ron’s¬†1948 Mercury was an absolutely stunning car. One of¬†Jim’s¬†all-time favorites. Ron drove it as regular transportation for a year or two before¬†trading it for a 1954 Ford Sunliner in late 1955.


CCC-ron-zimmerman-bertolucci-roten-03Sadly this photo is really badly weathered, but we can see the great stance of the car. The 1949 Mercury bumpers are a perfect touch for the car. 
[divider]

Ron has no idea what ever happened to his 1948 Mercury, and if it has survived all these years, or is long gone. Jim Roten mentioned that Ron’s ’48 Mercury went through several owners after Ron traded it. These new owners seriously abused the car. The last time Jim saw the Mercury was in 1958. By then, the car was in a very sad state of disrepair. If you have any more info on this car, please let us know.

Ross has been digging thru numerous old year books and is sharing all the car pictures he can find. Some photos, and memories in those books are really amazing. He found this photo of the old Bertolucci Mercury in the 1956 Chico High yearbook. The photo caption in the year book mentioned that the new owners of the Mercury had abused the Bertolucci car and you can see that in the yearbook shot it has a primed repair spot. It surely shows the beginning of the deterioration. Sad… Hopefully it surveilled. (Thanks for digging these up and sharing them Ross.)
[divider]




(This article is made possible by)




CCC-sponsor-ad-kustoms-illustrated-2016-01


[divider]




.

0

Jim Roten – 57 Mercury photos

JIM ROTEN – 57 MERCURY PHOTOS

Chico California had some very interesting Custom Cars in the later part of the 1950’s. Fortunately Jim Roten took photos of them, including these two 1957 Mercury mild Customs.

 
[dropcap]The[/dropcap] Mercury’s from 1957 have never really been a popular choice for customizing. They were huge cars to begin with, and when customized as in lowered they were a lot harder to drive than they already were straight from the factory. However that did not stop some people to turn their ’57 Mercury into show stopping Custom Cars. Jim Roten photographed two mild ’57 Mercury Montclair’s from his home town Chico. The first one we are highlighting here, was already customized when the car was brand new in 1957-58. This car was owned by Jim’s school mate¬†and friend,¬†Willis Kingsley Baker III. Willis was also known as¬†“King” Baker. The second Mercury, an rather¬†mild, an very stylish one¬†was probably¬†owned by¬†John Vincent at the time, who might have bought the Mercury to replace his customized ’54 Oldsmobile 88.
 
Many thanks to Jim Rotan for taking the photos back in the late 1950’s and his son Mike for sharing them.
 

Willis Kingsley Baker III Mercury – version one

Willis bought his 1957 Mercury new from the dealer and started to customize it right away. The car came from the factory as a two tone, in white and a darker color. Jim could not remember what the darker color was originally. Riley Collins shave all the emblems and removed the door handles, which he replaced with electric door openers. This all was done just weeks after Willis had bought the car. He had to work carefully since the idea was to leave the factory stock white in place, and only paint the darker color sections to hide the body work. With the soothing done, the body was taped off and Riley added a dark purple which was later scalloped and striped by Jim Roten. Jim thinks he scalloped the car in light purple, or lavender. 1957 Oldmobile¬†hubcaps were installed on medium wide white wall tires. The finishing touch for the outside was a set of Dummy Spotlights, an absolute mandatory item in the later part of the 1950’s.¬†The interior was re-upholstered with wonderful tuck & roll panels in white leatherette,¬†with a cover over the rear seats by Luckenbill’s Upholstery of Chico, California
 
CCC-jim-roten-58-merc-amn-02The early version of the car done in a simple two tone with elegant scallops. The long painted spread running from the front fender towards the rear quarter side trim created optical length. Possibly this was done to cover the shaved door handles. The hubcaps are stock 1957 Oldsmobile units.
[divider]
 
CCC-jim-roten-58-merc-amn-03A subtile scallop accentuates the recessed section on the trunk. The exhaust tips are moved from exiting on the lower side of the bumper, to the rear of the bumper where new tips exit thru the bumper.
[divider]
 
CCC-jim-roten-58-merc-amn-22At the rear we can see a LANCERS Chico club-plaque and some pin-striping by Jim Roten.
[divider]
 
CCC-jim-roten-58-merc-amn-04Willis Baker’s middle name was Kingsley, hence the nickname of “King”. ¬†Baker cleverly reversed the “M” in the grill to a “W”.¬†
[divider]
 
CCC-jim-roten-58-merc-amn-09The hood an top of the fenders show some very elegant scallops. Two rows of louvres where punched in the hood, and accentuated with thin scallops.
[divider]
 
CCC-jim-roten-58-merc-amn-21
 
CCC-jim-roten-58-merc-amn-05A little later a set of spotlights was added as well as a KUSTOMS of America plaque on the front bumper which was bought from George Barris in Los Angeles.
[divider]
 
CCC-jim-roten-58-merc-amn-06A better look at the wonderful subtile scallops on the hood and fender tops. This high view also shows that later the recess in the roof was painted in a different color.¬†Car owner Willis “King” Baker posing here with his freshly customized new ’57 Mercury. ¬†The car was driven regularly which explains¬†the bug splatted windshield.
[divider]
 
CCC-jim-roten-58-merc-amn-07King Baker demonstration how low the car was… LOW… but not low enough as the photos below show.
[divider]
 
 

Version two

About a¬†year after the first version of the King’s¬†Mercury had been finished,¬†it was time for a complete more radical redo. Riley painted the entire car in show quality dark metallic purple lacquer and Jim Roten¬†did the extensive scallops in light purple, or lavender metallic. We lowered the car as far as possible. The lower edge of the lake pipes was now about half the height of a pack of cigarettes above the ground! ¬†The “King’s Kart” logo on the decklid was applied by a sign painter. ¬†The car drew a lot of attention in Northern California but as a mild custom, eventually went to the scrapyard.
 
CCC-jim-roten-58-merc-amn-11Car was repainted dark purple metallic by Riley Collins. Jim Roten did the scallops and layout by hand using 1/4 inch masking tape. He then masked the entire car so light metallic purple scallops could be sprayed. Jim outlined the scallops with brush applied pin stripes.
[divider]
 
CCC-jim-roten-58-merc-amn-08This package of cigarettes demonstrates how low the car is. The lake pipes became protection for the lower body from getting damaged.
[divider]
 
CCC-jim-roten-58-merc-amn-17This is the only photo that has a date on it.  March 1958, and by that time the car was already in its second version. That is Jim Roten posing with the car shortly after he had finished striping the car.
[divider]
 
CCC-jim-roten-58-merc-amn-18Dead on side view of the car shows the nice scallops and outlines Jim Roten Designed. The car has a slight forward rake. Paint was show quality nitrocellulose lacquer.
[divider]
 
CCC-jim-roten-58-merc-amn-20
 
CCC-jim-roten-58-merc-amn-16The top of the fenders and hood show an well designed Scalloped layout which looks amazing on the smoothed body. Seemingly endless miles of striping.
[divider]
 
CCC-jim-roten-58-merc-amn-15The 1958 Mercury was named “Kings Kart” after Willis his nickname “King” Baker.
[divider]
 
CCC-jim-roten-58-merc-amn-14Another good look at the scallops on the hood and fender tops. The outlined section gives completely different proportions to the body. This photo also shows that the Oldsmobile hubcaps are now updated with some large bullets on the center.¬†The new tuck and roll interior was done by by Luckenbill’s Upholstery of Chico, California
[divider]
 
CCC-jim-roten-58-merc-amn-13King Baker with his freshly re-customized ’57 Mercury. ¬†The paint job was considered radical at the time. ¬†So was the low ride height. The lake pipes on Kings Mercury were actually functional.
[divider]
 

The¬†other ’57 Mercury Custom

Jim Roten took two photos of another 1957 Mercury Custom. This car was more subtile, and not as low as the one Willis owned. This Mercury was lowered only mildly, with all the handles and emblems shaved of the body and everything was smoothed. A very simple and elegant two tone was chosen for this car. The main body in a darker color and contrasting white only in the rear quarter/fender cove. Jim could not remember the colors of this Mercury.
 
CCC-jim-roten-58-merc-bku-02
 
CCC-jim-roten-58-merc-bku-01Turnpike cruiser skirts give this Merc a completely different look as well.
[divider]

 

(advertisement)

CCC-Sponsor-KKB-Ford-02-602

 
[divider]
 

CCC-Sponsor-Kustoms-Illustrated-602

 
[divider]
 
CCC-sledge-customs-sponsor-ad03-w
 
[divider]
 
 
.

0

Riley Collins 55 Chevy Cameo

RILEY COLLINS 55 CHEVY

In the later part of the 1950’s Riley Collins Custom Shop in¬†Chico California created some outstanding Custom Cars. Jim Roten designed many of them, including Riley’s personal 1955 Chevy Cameo shop truck.

 
[dropcap]Riley[/dropcap] Collins built this 1955 Chevy Cameo pick up truck for himself. And like a most of his other project cars his good friend Jim Roten was responsible for the the design. Mike Roten, Jim’s son shared one quick sketch Jim made in late 1958 for Riley’s Truck. It showed the use of 1958 Edsel taillights Caddy styled bumper ends and possible plans for full fender skirts. The Skirts and the Caddy bumper ends did not make it to the final version of the truck. But the whole rear fender / taillight treatment Jim designed sure did.
 
CCC-jim-roten-illustrations-09Jim Roten created this, and possibly a few more design sketches for the Riley Collin’s 1955 Chevy Cameo truck.¬†
[divider]
 
CCC-riley-collins-truck-01-jim-rotenThis is the earliest photo we have of Riley’s shop truck. Mostly stock with some of the bright work removed and the headlight treatment started.
[divider]
 
CCC-riley-collins-truck-09-jim-rotenTest fitting the Chrysler headlight in the opened up front fender.
[divider]
 
CCC-riley-collins-truck-02-jim-rotenAn early photo shows the work that was needed to install the 1958 Chrysler Imperial headlights. It also shows that at this point there were no plans for the Oldmobile grille surround/bumper set up yet, hence the metal work below the headlights.
[divider]
 
Riley started the truck with dropping the car 3 inches front using a dropped axle and the same amount at rear using a different set up for the springs, to get the perfect ride height. Jim had designed the car with a set of lake pipes, so Riley knew those would optical drop the car even further. All the stainless trim and door handles were shaved and the holes filled and smoothed for an nice smooth look. The doors are now operated using an electrical push button system.The front fenders were reshaped to accept a set of quad headlights taken from a 1958 Chrysler Imperial. The hood corners were rounded and now flow nicely into the shape of the Chevy headlights.
 
CCC-riley-collins-truck-06-jim-rotenThe early version finished in primer. The hood corners had not been rounded at this time.
[divider]
 
CCC-riley-collins-truck-03-jim-rotenBirds eye point of view shows the front end restyling on the truck. Spotlights have now also been added.
[divider]
 
CCC-riley-collins-truck-05-jim-rotenNotice how smooth the transition fro the Olds grille surround to the body is. I particular like the shape just underneath the hood and how it flows into the grille surround and headlights. This is very well designed and very well grafted restyling. Kudos to the Riley Collins and Jim Roten team.
[divider]
 
The whole grille unit was removed and an 1956 Olds front bumper/grille surround was installed. Riley hand made the body surround around this unit from round rod and sheet metal. The new front end changed the looks of the truck completely and gave it a very elegant appearance.

Another typical Jim Rotan design feature is the hand made grille. We have seen several of those in other Jim Rotan design sketches. (take a look at the¬†CCC-Article¬†on some of Jim Roten’s Custom Car designs sketches) Most of the grille was made from round rod, bend to shaped and welded into a single unit. Combined with two 1955 Buick bumper bullets¬†¬†before it was smoothed and send out to be plated. The new grille was place on to of a sheet of perforated chrome plated metal.
 
CCC-riley-collins-truck-07-jim-rotenRiley Collins standing with his 1955 Chevy Cameo.
[divider]
 
CCC-riley-collins-truck-08-jim-rotenSome fine tuning was done on the body work and Riley had the grille roughed in, still in need of smoothing and plating. The perforated metal sheet back section is still missing when Jim took this photo at Riley Collins Body shop.
[divider]
 
CCC-riley-collins-55-chevy-truck-01The finished truck at the Sacramento Autorama show, just after the car was finished in pearl white, and Jim Roten had taped the scallops with 1/4 inch tape and Riley Collins painted them withe 3-part candy red lacquer. (photo courtesy of Kent Collins)
[divider]
 
CCC-riley-collins-55-chevy-truck-02Great side view in front of the California National Guard building shows the nice flow of the candy red scallops. (photo courtesy of Kent Collins)
[divider]
 
CCC-riley-collins-55-chevy-truck-03A good look at the front of the truck with the hand made grille and very nicely done scallops which enhance the body styling Wheels are reversed chrome units with color detailed hubcaps added. (photo courtesy of Kent Collins)
[divider]
 
At the back Riley set out to duplicate Jim’s sketch as close as possible. He extended the fenders at the top with a hooded section. He later would fill this section with a very fine wire mesh insert. Below that he reshaped the rear fender and the tailgate to accept 1958 Edsel taillights flipped from side to side so that the downward section is now at the sides of the car and not towards the middle¬†as they are on the stock Edsel’s. The whole tailgate unit was completely reshaped and the shape of the rear quarter panels was extended onto the tailgate, and followed the shape of the Edsel taillights. The stock 1955 Chevy rear bumper-ettes were modified with round exhaust tips at the bottom. The non chrome center section was reshaped with a round rod license plate cover in the middle.
 
CCC-riley-collins-55-chevy-truck-04A lot of work went into the back of the truck as well where the flipped 1958 Edsel taillights are the center piece. Notice the roof insert in contrasting red. (photo courtesy of Kent Collins)
[divider]
 
CCC-riley-collins-55-chevy-truck-05Rer 3/4 view of Riley Collins 1955 Chevy Cameo. Not shown in these photos is the special made tonneau cover. (photo courtesy of Kent Collins)
[divider]
 
With all the body work completed Riley primered the body work and drove it around for a bit before he would paint it “mother of pearl” white with candy red accents. The interior was done in white naugahide with red inserts. Jim Roten mentioned that the engine compartment looked as good as the exterior. It had a 265 Chevy small block equipped with a Duntov cam, solid lifters, multiple carburetion, Corvette valve covers, headers, and glasspack mufflers. And it sounded as good as it looked. Even the front fender liners were chromed plated. Basically a ’56 Corvette engine in a truck! In those days few customs had hot engines, but this one did.

Riley sold his truck in the late 1960’s or early 1970’s. And we have no idea what happened to it after that. Does anybody have a clue where this one is today? Or what happened to it?

CCC-riley-collins-55-chevy-truck-06An other paint job shows a different design for the scallops and all white around the grille surround. (photo courtesy of the Barris Collection)
[divider]

CCC-riley-collins-55-chevy-truck-07

CCC-jim-roten-illustrations-19This version of the Riley Collins Shop Truck was featured in the Custom Show-Cars Trend book 181 from 1959.
[divider]

 
Special thanks to Jim and Mike Roten and Kent Collins for sharing the photos for this article.
 
 
 

[divider]

 

(advertisement)

CCC-Sponsor-Kustoms-Illustrated-602

 
[divider]
 

Kustom Kar Books Golden Sahara

 
[divider]
 
CCC-sledge-customs-sponsor-ad03-w
 
[divider]
 
 
.

0

Jim Roten Custom Car Designs

JIM ROTEN DESIGNS

Jim Roten was close¬†friends with Riley Collins, who ran a Custom Body show in Chico Ca. This article shows some of Jim Roten’s¬†amazing design sketches he made for Rileys Customs.

 
(Special thanks to Mike Roten, Jim’s son for scanning his father’s illustrations and photos)

Mike Roten send us these amazing scans he made of his fathers designs. Jim recieved these sketches in an envelope from Riley’s wife after Riley had passed away. Jim had not seen these since he created them in the mid to late 1950’s. They brought back many memories. Jim handed the envelope over to his son Mike. Who scanned some of the material to share with the Custom Car Chronicle.

The envelope contains over 100 sketches so what we show you here is just the tip of the iceberg. We hope to be able to show you many more of these amazing sketches in the near future. Most of the sketches in the envelope were created for Rileys Custom projects, but a few might have been for other projects.

Mike calls them the ‘red’ sketches. They are¬†all are done on identical sheets of 5×7 newsprint in red pencil. Some of them are really well detailed, others are just quick idea sketches. Most of these illustrations might have never made it into reality, but some of the designs we recognize. If you see something in these illustrations that you can remember from the late 1950’s or early 1960’s. Please let us know. We would love to be able to identify some of the cars in the sketches.

CCC-jim-roten-illustrations-16(A) We start with a photo Mike took of some of the content of the envelope. This particular sketch was made with regular gray pencils. Mildy customized Shoebox 1950 FordClub Coupe.
[divider]

CCC-jim-roten-illustrations-17(B) Better look at the side view and rear fender modifications designed by Jim.
[divider]
 
CCC-jim-roten-illustrations-15(C) 1953 Ford Sedan project. Nice use of side trim, quad headlights, pancaked hood, tubular grille and 1955 Pontiac Split bumpers. Very elegant. 
[divider]
 
CCC-jim-roten-illustrations-14(D) 1958 Ford front end design. With pancaked hood with rounded corners. Toothed grille bar and reworked bumper. I also love the hood scoop.
[divider]
 
CCC-jim-roten-illustrations-13(E) Most of the designs Jim made are based on milder custom cars. But this 1950 Mercury was a full custom concept, named the Wildest Big M of them all! Jim’s designs call for a huge amount of body work including a wrap around windshield, quad headlights. Sectioned body with coved behind the front wheel openings, hood and rear quarter scoops, extended rear fenders, split bumpers and floating toothed grille. WILD.
[divider]
 
CCC-jim-roten-illustrations-12(F) Possibly based on a 1957-58 Mercury with a lot of mild but wild reshaped body panels, new bumpers based on Oldsmobile units and an outline and scalloped paint job.
[divider]
 
CCC-jim-roten-illustrations-11(G) Another sketch based on a 52-54 Ford shows coved panels behind the wheel openings, bullet rille with vertical placed quad headlights in reshaped fenders. Finned rear fenders with quad pointy taillights. Jim Roten 1959.
[divider]
 
CCC-jim-roten-illustrations-10(H) Perhaps created for the same owner as the openings photos these quick sketches show some ideas for a 1950 Ford Club Coupe. This one is chopped and converted to a hard-top body style with a larger rear window. Edsel styled taillights and possebly Studebaker pans used to create the front and rear grille openings. Jim also created a really nice two tone paint option using the side trim and scallops.
[divider]
 
CCC-jim-roten-illustrations-09(I) This is one of the sketches we can identify. This one was designed for the Riley Shop Truck based on a 1955 Chevy Cameo.
[divider]
 
CCC-jim-roten-illustrations-18Under construction photo of the truck from Jim’s Personal collection. Sadly none of Jim’s photos showed the work done on the taillights to show how his sketch was used by Riley Collins. But fortunately we can see that in the finished truck photos below.
[divider]
 
CCC-jim-roten-illustrations-19The finished Riley Collins Shop Truck was featured in the Custom Car Annuals.
[divider]
 
CCC-jim-roten-illustrations-20

CCC-jim-roten-illustrations-02(J) Another Pick-Up project was this 1957 Ford truck. Some body work, but the wildest part was the nice paneled and flame paint design Jim came up with.
[divider]
 
CCC-jim-roten-illustrations-08(K) Perhaps my personal favorite of them all is this very stylish 1955 Chevy mild custom. Oldsmobile grille/bumper surround with hand made center. Canted quad headlights, reshaped and rounded hood opening. Wonderful use of side trim, cruiser skirts, again coved panels behind the front wheels and a nice two tone paint job. Somebody really should build this one.
[divider]
 
CCC-jim-roten-illustrations-07(L) Another sheet with some quick sketches/ideas for a few projects.
[divider]
 
CCC-jim-roten-illustrations-06(M) This looks to be based on a early-mid 1950’s four door Cadillac to which added fins on the rear fenders.
[divider]
 
CCC-jim-roten-illustrations-05(N) Another really great design is this one based most likely on a 1952-54 Ford or Mercury. Jim designed it with an heavy chop, quad headlights, Studebaker pan shaped grille opening, pancaked hood and again a really nice two tone paint job with clever use of custom side trim, outlines and scallops.
[divider]
 
CCC-jim-roten-illustrations-04(O) Jim designed the 1955 Mercury of Ray Cress. You can see more about the Ray Cress Mercury in the CCC-Article.
[divider]
 
CCC-jim-roten-illustrations-03(P) Interesting design ideas using Edsel taillights on a 52-54 Ford Coupe.
[divider]
 
CCC-jim-roten-illustrations-01(Q) The text Jim wrote to go along with this 1956 Ford Victoria design says it all. Another very wild and well balanced design.  
[divider]
 

[divider]

 

(advertisement)

Kustom Kar Books Golden Sahara

[divider]
 
 
.

0

Ray Cress 56 Mercury

 

RAY CRESS 56 MERCURY

 

Designed by Jim Roten and built, mostly by the Riley Colins Custom shop for owner Ray Cress, this uniquely restyled Mercury was published frequently and could be seen on several magazine covers in the late 1950’s.



(Special thanks to Mike Roten, Jim’s son for scanning his father’s photos and illustrations)


[dropcap]T[/dropcap]he first time I saw a photo of the Ray Cress ’56 Mercury was in Pat Ganahl’s the American Custom Car book in 2001. I was very impressed with this mild but well restyled Custom. And especially the color, lime gold with subtile gold scallops made a huge impression on me. There were two photos in the book. One, full spread on the title page and a smaller one inside. Both scanned from nice color slides. The photo caption mentioned the car was built by Riley Custom Shop in Chico, California. I have to admit that back then I had never heard of this Custom Shop. But later I sure would find out much more about it.

¬†Ray’s Mercury

Ray Cress took his near new ’56 Mercury Hardtop to the Ray’s Custom Shop in Chico California. Here the back pat of the car was roughly restyled. Later Ray Cress took the car to Riley Collins in Chico California (Chico is around 75 miles north of Sacramento). Ray wanted a full custom, but still on the mild side, not chop, but with new front and rear and many other body restyling. Close friend and shop employee of Riley, Jim Rotan was asked to make some design sketches of what the Owner had asked for and Jim¬†came up with together with Riley. A wonderful low creation with some new body lines and a very elegant redesigned front end. Ray approved the final design for his new Custom, and Riley went to work.¬†The approved sketch¬†Jim Roten made in 1957 can be seen below.



CCC-ray-cress-56-mercury-06The original Jim Roten design sketch from 1957. This version was approved by Ray Cress.
[divider]



Starting at the front Riley removed the stock bumpers and replaced them with an ’56 Oldsmobile bumper. The lower grille opening in the Old bumper dictated the shape of the new grille opening on the top, which was created from bended round tubing welded and molded to the front fenders and lower hood section. The front lower hood section was welded to the fenders, and a new higher hood line was cut , in the process the corners were rounded for a more elegant look. The front fenders were extended and a new opening was created using round tubing for an “hooded” effect. The original headlights was set in a chrome plated mesh screen. A new grille was created according Jim’s designs. Chrome expanded metal was used as a background, and in front of that hand shaped chrome tubing was used. On the lower corners two small diameter chrome bullets were added.



CCC-ray-cress-56-mercury-14Parked in front of the Riley Collins Custom Shop in Chico is the freshly painted and assembled Mercury. Still missing are the gold scallops at this point Jim took this photo.
[divider]


CCC-ray-cress-56-mercury-12Jim Roten took this photo of the nearly completed Mercury. The expanded metal and the two bullets are still missing from the grille and so are the Olds parking light.
[divider]


 


CCC-ray-cress-56-mercury-13Again parked at Riley’s shop, but now the gold scallops have been added.
[divider]



At the rear,¬†Ray’s Body Shop had previously installed a set of ’56 Packard taillights in extended rear fenders. Below the Packard taillights Riley used 1954 Cadillac bumper ends and routed the exhaust from the mercury to fit the new Cadillac bumper end exhaust tips. The center section of the bumper was replaced with an body colored splash pan/roll pan. Round tubing was used to made an double roll on this panel that optically leads to the license plate on the back. Moving to the side of the car we can see that Jim had re-disigned the quarter panels to have working scoops front and rear, and long fender skirts. Riley removed the chrome from the quarter panels and cut out the top leading edge and created the¬†elegantly¬†shaped scoops. He reworked a set of 1957 Mercury¬†cruiser skirts to fit the ’56 Mercury. A¬†1957 Ford side trim was cut down at the back and used instead of the stock unit.




CCC-ray-cress-56-mercury-11Completely finished with new completed grille and scallops.
[divider]



All handles and emblems were shaved and Riley sprayed the car in a wonderful lime gold color. Later followed by scallops, designed and taped by Jim Roten, in metallic gold. The scallops were outlined in dark gold by Jim. The car was lowered to the max and a set of wide white wall tires with chrome reverse wheels with¬†custom hubcaps and¬†chrome fake knock-offs was added. To make the car look even lower a set of full length lake pipes was added.¬†Luckinbill‚Äôs Custom Upholstery Shop in Chico is responsible for the fine white and lime gold tuck & roll interior.¬†Ray’s mercury¬†was on the cover of the May 1958 Motor Life magazine and Custom Cars magazine Jan, 1959 (small photo) with two pages inside. The car was also feature in the May 1959 issue of¬†Car Craft¬†magazine and a full page with three photos in the Trend Book 181 Custom Show-Cars published in 1959.



CCC-ray-cress-56-mercury-02In 1958 Ray’s Mercury was nominated as one of 28 “Top Customs of the Year” in Motor Life July 1958, and a photo of the car was featured on the cover of the magazine. Ray’s Mercury ended at the third place, not bad at all.
[divider]


CCC-ray-cress-56-mercury-07


CCC-ray-cress-56-mercury-04


CCC-ray-cress-56-mercury-05A closer look at the ’54 Cadillac bumper ends, ’56 Packard taillights and hand made scoops. Notice how the lower edge of the scoop swoops into the bottom of the Packard taillight and top of the Caddy bumper. Nice touch.
[divider]


CCC-ray-cress-56-mercury-151957 Ford side trim was cut off so it would fit the Mercury body and disappear in the custom scoop. 
[divider]


CCC-ray-cress-56-mercury-03



The Stan Duncan Version

After showing the car for a few seasons Ray Cress sold the Mercury to Stan Duncan. Stan had the car repainted in a deep tangerine with different shaped scallops than before done in gold fades and gold outlines. The car in the Stan Duncan version appeared on the cover of the March 1959 and had a full spread on the inside.



CCC-ray-cress-56-mercury-01The new tangerine paint with gold fading scallops. The rest of the car remained as Ray had it first.
[divider]


CCC-ray-cress-56-mercury-10Stan nick-named the Mercury the “Golden Touch”.
[divider]


CCC-ray-cress-56-mercury-09 CCC-ray-cress-56-mercury-08Car Speed and Style magazine spread.
[divider]




CCC-ray-cress-56-mercury-end


Resources and more info

  • Motor Life, magazine July 1958
  • Custom Cars, magazine Januari 1959
  • Car Speed and Style, magazine March 1959
  • Car Craft, magazine May 1959
  • Custom Show-Cars, booklet Trend Book 181 ¬†published in 1959
  • Classic & Custom, magazine Jan, 1984
  • American Custom Car, book Pat Ganahl, 2001


 

[divider]




CCC-Sponsor-Kustoms-Illustrated-602[divider]



ccc-sponsor-ad-customs-by-flash-w

[divider]





.

0

Jim Roten Photos 1956 Sacramento Autorama part 2

’56 SACRAMENTO AUTORAMA PHOTOS PART 2

Part two of the series of photos Jim Roten took at the 1956 Sacramento Autorama show.

Jim Roten, who worked for Riley Collins Body Shop in Chico, California, was very active in the Custom Car scene in the mid to late 1950’s. And fortunately for us, he also like to take photos. He usually brought his camera where ever he went with his own customized 1952 Ford convertible. Jim also brought his camera when he visited the Sacramento Autorama¬†Show in 1956. Let take a look at some more photos from in the second, and last part of this series.

Enjoy this second part of the Jim Roten 1956 Sacramento Autorama SHow photos.

[box_light]Check out part one of the Jim Roten 1956 Sacramento Autorama Show article.[/box_light]

CCC-jim-roten-indoorshow-03-WThe Barris Kustom Shop brought the 1953 Cadillac “Le Mans” to the show. This photo shows the team preparing the car on set-up day for the public the next morning. The “Le Mans” Custom Cadillac was based on one of the three experimental show cars created by GM at the Motorama shows. The Barris shop built it for Harry Karl, who gave it to his wife, actress Marie MacDonald.

 

CCC-jim-roten-indoorshow-02-WTop and Bottom show the mildly customized, 1953 Ford of Ervin G. Castro from Oakland with extended rear fenders and incorporated continental kit.

 

CCC-jim-roten-indoorshow-16-W

 

CCC-jim-roten-indoorshow-05-WHarry Fruzza’s 1955 For F-100 with early style flames and pinstriped bumper.

 

CCC-jim-roten-indoorshow-27-WJohnny Zupan took the Louis Bettancourt Ayala/Barris 1949 Mercury back to the Barris Kustoms Shop in the mid 1950’s for a make-over. The car was shown at the 1956 Sacramento Autorama¬†Show with all new paint but the scallops had still to be outlined in bold white striping by Dean Jeffries.

 

CCC-jim-roten-indoorshow-26-WUnidentified channeled roadster with sectioned ’32 Ford grille with white insert, and ripple disk full moon hubcaps. Beautiful detailed flathead engine with three carb set up.

CCC-jim-roten-indoorshow-25-WUnknown channeled ’32 Ford Roadster with sectioned grille and three carbed full detailed flathead engine. Net to it sits a dual cab Ford by Dick Bertolucci.

CCC-jim-roten-indoorshow-22-W2Bill Montero’s model A with 32 Ford fenders and grille.

CCC-jim-roten-indoorshow-21-W2Built by owner Frank Rose of A & R Auto Mart in Oakland, California, 1927 Ford Model-T Roadster Home made frame with chrome plated Ford tube front axle. The grille is a sectioned ’32 Ford unit with a hand built grille insert, created from round stock and chrome plated. Body work by Jack Hagemann. The fenders, bellypan, instrument panel, hood, deck lid, and the panel below the deck lid was hand formed from aluminum.. The car was painted jet black lacquer with scalloped and striped in white and blue by Tommy the Greek. (info from Kustomrama)

 

CCC-jim-roten-indoorshow-18-WUnknown 1951 Chevy Hard-Top with hooded headlights, Pointac grille and two tone paint job seperated by the 1954 Oldsmobile side trim. Parked next to it is the all white 1932 Ford built by Harry Westergard and Dick Bertolucci.

 

CCC-jim-roten-indoorshow-17-WAnother unidentified custom is this Shoebox Ford with extreme rounded hood corners. 1956 Plymouth grille and 1955-56 DeSoto side trim.

 


CCC-jim-roten-indoorshow-13-W1953 Chevy with very interesting taillight and side trim details, created by Gordon Van of Oakland for Brian Bernon.

 

CCC-jim-roten-indoorshow-12-W

 

CCC-jim-roten-indoorshow-09-WDick Katayanagi 1954 Ford F-100 Pick up with abstract flames

 

[box_light]More on the Jim Roten Collection can be seen in the other articles we have created on the Custom Car Chronicle.
Check out part one of the Jim Roten 1956 Sacramento Autorama Show article.[/box_light]

[divider]

More info and resources 

  • The Oakland Roadster Show, Book by Andy Southard, Jr and Dain Gingerelli
  • Hot Rods of the 1950s, Book by Andy Southard, Jr
  • Kustomrama website, Hot Rod information

 

[divider]

(advertisement)

Kustom Kar Books Golden Sahara

[divider]

CCC-Sponsor-KingKustomsTShirt-602Contact Rob Radcliffe at King Kustoms for more info on these T-Shirts Email Rob

[divider]

CCC-Sponsor-LJB-602-B

.

0

Jim Roten Photos 1956 Sacramento Autorama Show

’56 Sacramento Autorama¬†SHOW PHOTOS

Jim Roten from Chico California took a lot of photos of the custom car around him in the mid 1950’s. He also brought his camera to the 1956 Sacramento Autorama¬†show and took dozens of snapshots at Set Up Day.

Jim Roten worked for Riley Collins Body Shop in Chico, California. He owned a wonderful mild 1952 Ford convertible custom, which we will highlight in a separate article in the near future. This car was also the work of his friend Riley Collins. We are very fortunately that Jim loved to take photos. And took many photos of the cars that were created in Riley’s shop, the cars his friends owned. And like we can see in this article the cars he photographed at some of the car shows he visited back in the mid 1950’s. This two part article will cover the photos Jim took at the 1956 Sacramento Autorama¬†Show. Mostly Custom Cars, but Jim also took some photos of the Hot Rods he liked.
So, sit back and enjoy the show!

[box_light]Check out part two of the Jim Roten 1956 Sacramento Autorama Show article.[/box_light]

CCC-jim-roten-indoorshow-01-WEd Rincon’s 1951 Mercury started by Harry Westergard and finished by Dick Bertolucci. On the left we can see another Westergard custom. Most likely Butler Rugard’s 1946 Chevy. The cars are being polished and prepared for the show during Set Up Day.

 

CCC-jim-roten-indoorshow-07-WChuck DeWitt’s Barris-built shoebox convertible. Interesting to see it in two tone, with white below the side trim. 1953 Cadillac hubcaps have replaced the wire wheel hubcaps the car used in its original version.

 

CCC-jim-roten-indoorshow-04-WJack Bertlow from San Jose’s is preparing his Shoebox with 1955 Ford grille. A very nicely done mild custom.

 

CCC-jim-roten-indoorshow-06-W1952-54 Ford HT with hand made waterfall grille. Very similar to what Sam Barris used in his 1952 Ford convertible.

 

CCC-jim-roten-indoorshow-10-W21950 Ford sedan with Packard grille. On the left we can see the front fender and bumper of Tom Hocker’s 1940 Ford built by the Barris Kustom Shop.

 

CCC-jim-roten-indoorshow-24-WBuilt by Harry Westergard and painted white by Dick Bertolucci.

 

CCC-jim-roten-indoorshow-23-WIvan Scorsur from San Jose home built, channeled ’32 Ford Roadster.

 

CCC-jim-roten-indoorshow-20-W2Frank Chisello 1952 ford with 1955 Ford grille.

 

CCC-jim-roten-indoorshow-19-WGeorge Sein’s 1932 Ford 5-window Coupe restyled by the Barris Kustom Shop.

 

CCC-jim-roten-indoorshow-15-WDon Coulter’s Barris Kutoms restyled 1955 Oldsmobile getting pollished for the show.

 

CCC-jim-roten-indoorshow-14-WGene Winfield 1950 Mercury with 1951 rear fenders and flipped Lincoln side trim. The floating grille was made from Mercury accessory bumper overriders.

 

CCC-jim-roten-indoorshow-11-WJoe Bailon created this HT Shoebox for Elton Kantor.

 

[box_light]More on the Jim Roten Collection can be seen in the other articles we have created on the Custom Car Chronicle.
Check out part two of the Jim Roten 1956 Sacramento Autorama Show article.[/box_light]

 

More info and resources 

  • The Oakland Roadster Show,¬†Book by Andy Southard, Jr and Dain Gingerelli
  • Hot Rods of the 1950s,¬†Book by Andy Southard, Jr

[divider]

(advertisement)

Kustom Kar Books Golden Sahara

[divider]

CCC-Sponsor-KingKustomsTShirt-602Contact Rob Radcliffe at King Kustoms for more info on these T-Shirts Email Rob

[divider]

CCC-Sponsor-LJB-602-B

.

0

John Vincent 1954 Oldsmobile

 

VINCENT 1954 OLDSMOBILE

 

Riley Collins from Chico, California created this 1954 Oldsmobile semi-custom. Jim Roten took the photos.



Riley Collins, had a body show in Chico California. Riley was a famous custom car builder, mostly in the Chico area, but he also created some customs that made it in the magazines.  His good friend, Jim Roten worked part-time with him in the shop. Jim was the designer of the team. And Riley the guy doing the actual metal work and paint. The Riley Collins Custom Car we are highlighting here is an 1954 Oldsmobile 88. It was originally built for John Vincent and later owned by Calvin Keeman. The car, classified as semi-custom, was subtile, but the team of Riley and Jim restyled it enough to make this car a show winner at many shows.

Riley smoothed the body, shaved the handles. At the front he installed 1953 Buick headlights and molded in the top grille bar. The bumper guards where removed and replaced with bullet units from a 1955 Cadillac. The opening was filled with a rectangular mesh chrome plated grille. In the later version some smaller bullets were added to it. At the rear the rear fenders were reshaped to accept 1954 Packard taillights. The back up lights were removed in the process as well. The car was painted maroon for the first edition. The lighter color on the top and above the side trim is unknown. In the later version the car was repainted in Candy Red. The photos below show to car in three different stages.
The photos were all taken by Jim Roten and come from his personal Collection. 


CCC-ron-vincent-54-olds-02-WThe 1954 Packard taillights make the rear of the Oldsmobile really interesting.


CCC-ron-vincent-54-olds-09-WTo get the car low the rear of the frame was z-ed.


CCC-ron-vincent-54-olds-01-W


CCC-ron-vincent-54-olds-06-WThis photo shows a small portion of the wonderful wide pleated interior done in two tone maroon. This photo shows the newly added lake pipes.


CCC-ron-vincent-54-olds-10-W


CCC-ron-vincent-54-olds-07-WOwner demonstrates how low the car is, especially with the new lake pipes installed. This photo gives us a good look at the Buick headlights and how great they look on this Oldsmobile.


CCC-ron-vincent-54-olds-05-WJohn Vincent’s ’54 Olds 88 at the 1956 Sacramento Autorama


CCC-ron-vincent-54-olds-03-WSome times later small scallops with bold white pin-striping was added to the car.


CCC-ron-vincent-54-olds-04-WSubtile scallops on the top of the rear fenders.


CCC-ron-vincent-54-olds-08-W

Rod & Custom Magazine featured the ’54 Oldsmobile in the March 1961 issue. By then the car was owned by Calvin Keeman. The car was now repainted in candy for the complete body. New for this version are the addition of¬†Cruiser Skirts and the bullets on the mesh grille.


[divider]


CCC-donating-sponsor-ad-03


[divider]

(this article is sponsored by)

CCC-sponsor-ad-kustoms-illustrated-2016-01


[divider]






.

0